February 16, 2022
-
Supports
Technical Support Email
support@innovativeelectronics.com
If you have trouble on the usage of our products (except for DT-51 Trainer Kit)tutorial51@innovativeelectronics.com
If you have trouble on the usage of our DT-51 Trainer Kit productsiewebmaster@innovativeelectronics.com
If you have any feedback relating to the IE Website Design -
Technical Support Email
support@innovativeelectronics.com
If you have trouble on the usage of our products (except for DT-51 Trainer Kit)tutorial51@innovativeelectronics.com
If you have trouble on the usage of our DT-51 Trainer Kit productsiewebmaster@innovativeelectronics.com
If you have any feedback relating to the IE Website Design
DT-I/O I²C Peripheral
DT-I/O product
DT-I/O I2C Peripheral is a module that consists optional 8-bit Analog-to-Digital & Digital-to-Analog Converter (ADDA), serial EEPROM, and Real-Time Clock (RTC) DS1307. All of the peripherals are accessible through I2C interface. You can use this module in many applications such as temperature monitoring, motor controller, attendance, datalogger, digital clock, robot, etc.
Dimension : 5,85 cm (L) x 5,05 cm (W) x 2,5 cm (H)
- Product Detail
- Download
- Application Note
Specifications :
- 8-bit ADDA PCF8591 with '000' address (optional):
- 4 channel ADC input, can be programmed as single ended or differential input.
- 1 channel DAC output.
- Maximum conversion time for ADC and DAC = 90 us.
- Maximum linearity Error for ADC and DAC = 1,5 LSB.
- VREF = 2,5 Volt (using LM336-2.5V).
- Analog input range: 0 - 2,5 Volt (single ended input), -1,25 - +1,25 Volt (differential input).
- Analog output range: 0 - 2,5 Volt.
- 1 output pin for internal osilator.
- RTC:
- Counts second, minute, hour, date, month, day, and year in Binary-coded Decimal (BCD) format.
- Leap year compensation until year 2100.
- 2 hour mode: 12 hours (AM/PM) dan 24 hours.
- 56 byte Nonvolatile SRAM.
- 3 VDC Lithium backup battery.
- 1 pin output for square wave signal with programmable frequency (1 Hz, 4 kHz, 8 kHz, atau 32 kHz).
- Serial EEPROM:
- 1x AT24C01A (1 Kbit) with '000' address.
- 2 sockets 8-pin DIP for AT24Cxxx, with '001' and '011' address.
- I2C serial interface, only 2 lines needed, for data and clock.
- 5 VDC working voltage.
Includes :
- 1x Board DT-I/O I2C Peripheral.
Application Note Table
| Article | File | Desc | date |
|---|---|---|---|
| |
AN210.zip | [AN210] Temperature Logger berbasiskan DT-AVR Inoduino dengan SD Card sebagai Media Penyimpanan DataThis application note will explain how to build a temperature logger system. This application note uses DT-AVR Inoduino, DT-I/O I2C Peripheral, DT-SENSE Temperature Sensor, EMS SD/MMC/FRAM, and EMS LCD Display. |
28-04-2014 |
| |
AN204.zip | [AN204] Automatic Relay Control Based Google CalendarThis application note will explain how to build an automatic relay control based system. This application note uses DT-I/O TCP/IP To UART Converter, DT-AVR ATMEGA128L Bootloader Micro System, DT-I/O I2C Peripheral, and DT-I/O Relay Board Ver 2.0-1201 |
28-04-2014 |
| |
AN146.zip | [AN146] Programmable Relay BoardThis application note will explain how to use DT-I/O Relay Board Ver 2.0 as programmable relay board. This application note uses DT-51 Low Cost Micro System, DT-I/O I2C Peripheral (consists of serial EEPROM and RTC DS1307), and DT I/O Relay Board Ver 2.0 (could be changed to DT-I/O Neo Relay Board). |
28-04-2014 |
| |
AN122.zip | [AN122] USB to I²C Peripheral BridgeThis application note will explain how to use PC-Link USBer as a USB to I2C converter. This application note uses PC-Link USBer and DT-I/O I2C Peripheral. |
25-04-2014 |
| |
AN111.zip | [AN111] Calendar Digital IIThis application note will explain how to build digital calendar. This application note uses DT-51 Minimum System Ver 3.0, DT-I/O Graphic LCD 12864 Yellow Green Backlight / DT-I/O Graphic LCD 12864 Blue STN White Backlight, and DT-I/O I2C Peripheral. |
25-04-2014 |
Raspberry Pi Home Remote App Kit
June 05, 2018
April 12, 2017
April 12, 2017
June 02, 2016
June 02, 2016
June 02, 2016
April 27, 2016
