February 16, 2022
-
Supports
Technical Support Email
support@innovativeelectronics.com
If you have trouble on the usage of our products (except for DT-51 Trainer Kit)tutorial51@innovativeelectronics.com
If you have trouble on the usage of our DT-51 Trainer Kit productsiewebmaster@innovativeelectronics.com
If you have any feedback relating to the IE Website Design -
Technical Support Email
support@innovativeelectronics.com
If you have trouble on the usage of our products (except for DT-51 Trainer Kit)tutorial51@innovativeelectronics.com
If you have trouble on the usage of our DT-51 Trainer Kit productsiewebmaster@innovativeelectronics.com
If you have any feedback relating to the IE Website Design
DT-I/O Neo Relay Board
DT-I/O product
DT-I/O Neo Relay Board is a relay board which consist of 8 SPDT mechanical relays. Each relay has equipped with LED indicator and Normally output pin, normally close pin and COM pin.
Note : This module requires definite logic input (High/Low) when connected to the pwoer supply. Therefore requires external 1K Ohm pull-down resistor for each I/O in order to connect to the GND for each I/O.
Dimension : 16,1 cm (L) x 8,4 cm (W) x 1,9 cm (H)
- Product Detail
- Download
- Application Note
Specifications :
- Consist of eight mechanical relays (NO, NC and COM).
- Uses plugable terminal block, thus simplifying in intalation external device to the relay contact.
- Each relay comes with LED indicator (On/Off).
- 5VDC input voltage.
- Equipped with EMI filter on input voltage line to reduce noise.
- TTL/CMOS I/O compatible.
- Comes with delay feature to protect external device from unstate condition and prevent of RFI
- Free pad for external MOV between NO and COM or NC and COM.
- Fully compatible with DT-51 Low Cost Series and DT-AVR Low Cost Series, also compatiblw with DT-51 Minimum System, PertraFuz, DT-BASIC and another microcontroller board.
- Other product options :
- DT-I/O Neo Relay Board 0510: uses 5V relay with 10A/250VAC for contact rating.
- DT-I/O Neo Relay Board 1210: uses 12V relay with 10A/240VAC for contact rating.
- DT-I/O Neo Relay Board 2410: uses 24V relay with 10A/250VAC for contact rating. (discontinued)
Includes :
- 1x DT-I/O Neo Relay Board.
Application Note Table
| Article | File | Desc | date |
|---|---|---|---|
| |
AN171.zip | [AN171] Smart Monitoring and Control System dengan menggunakan jalur komunikasi RS-485This application note will explain how to build a simple smart monitoring system. This application note uses DT-I/O USB to UART Converter, DT-I/O NEO RS-232 to RS-485 Converter, DT-I/O Neo Relay Board, DT-Sense Barometric Pressure & Temperature Sensor, DT-AVR Low Cost Micro System, and DT-AVR Low Cost Nano System. |
28-04-2014 |
| |
AN159.pdf | [AN159] Kendali Relay dengan Remote TVThis application note will explain how to use television remote control to turn on some electronic devices. This application note uses SPC IR Transceiver, DT-AVR Low Cost Micro System, and DT-IO Neo Relay Board. |
28-04-2014 |
| |
AN151.zip | [AN151] Ekspansi 2 Pin I/O AVR Menjadi 8 Input/OutputThis application note will explain how to expand AVR's I/O pins. This application note uses DT-AVR Low Cost Nano System/DT-AVR Low Cost Micro System, DT-I/O I²C to Parallel Converter, DT-I/O Neo Relay Board, and DT-I/O 4 x 4 Keypad Module. |
28-04-2014 |
| |
AN146.zip | [AN146] Programmable Relay BoardThis application note will explain how to use DT-I/O Relay Board Ver 2.0 as programmable relay board. This application note uses DT-51 Low Cost Micro System, DT-I/O I2C Peripheral (consists of serial EEPROM and RTC DS1307), and DT I/O Relay Board Ver 2.0 (could be changed to DT-I/O Neo Relay Board). |
28-04-2014 |
Raspberry Pi Home Remote App Kit
June 05, 2018
April 12, 2017
April 12, 2017
June 02, 2016
June 02, 2016
June 02, 2016
April 27, 2016
